Smart reset tool

Hard drive smart is one of the most important factors to judge the health of the hard drives. If it has values on different items contained in the Smart table, the drives are usually considered as second-hand hard drives. To refurbish the hard drives, the very first thing is to reset the smart. Smart table contains usually the following parameters:. If the hard drive is ready and detected, users can use DFL firmware repair tools to reset the smart by one simple click.

If the hard drive has firmware damage and not detected, users need to use DFL firmware repair tools to fix the firmware failures and then reset the smart.

If you want to reset your smartphone without risk and danger, universal hard reset tool is perfect for you. Download it from here. After download, install it on PC or laptop. Remember that, your PC must have. NET framework. You get. NET framework from Microsoft official website. Run it, and connect your smartphone to USB cable. You can check all of your mobile information with this tool. Download this android reset tool exe file from here.

Before restoring a factory Android, keep in mind that this removes all data from the internal memory of the device. If possible, make a backup of the data before proceeding. This is the method to use if the phone is working on a regular basis. Only the buttons are released when the LG logo appears. The cell phone starts already formatted. If the cell phone does not start or has a serious failure, this is the alternative you should try. The recovery mode recovery, in Spanish is a special system on Android devices that offers some advanced options to recover the device in case of failures or problems.

Among them is the factory reset factory reset. Start the cell phone in recovery mode. With the cell phone off, simultaneously press the power button and turn up the volume and start button, if one exists. Actually there is a way to reset S. You only need simple rs to usb converter uart to ttl and a few cables attached to hdds diagnostic interfaces.

That's why it says "failed in the past", not "failing now": you did just barely touch the max-temp threshold. Note the attribute display shows "normalized: 50, threshold: 45, worst: 45". These are You also have some bad sectors uncorrectable sector errors , so whether the brief high temperature caused that or not, it's probably time to ditch that drive.

The software you're using looks like it's only showing the current temp, which is slightly below the threshold, but it's not going to hide the fact that the drive was out-of-spec at some point in the past. You could certainly justify ignoring that momentary high-temperature, if you really did correct it in minutes. But you won't or shouldn't ever be able to make the drive itself lie about the fact that it was over its rated max temp for some time, and thus the attribute did fail in the past.

You can configure smartd to ignore any given attribute so you can still get a useful notification if anything else crosses a threshold into officially-failing territory. ID must be a decimal integer in the range from 1 to This Directive modifies the behavior of the '-f' Directive and has no effect without it. This is useful, for example, if you have a very old disk and don't want to keep getting messages about the hours-on-lifetime Attribute usually Attribute 9 failing.

This Directive may appear multiple times for a single device, if you want to ignore multiple Attributes. The drive has only been powered on for a couple minutes; that's presumably why there's a - for no data in some of the fields. If you drive has these extended attributes, you can show someone that the time spent outside of allowed temp was very short if that's the case. The thinking is that an overheat increases your chances for failure.

SMART isn't saying your drive is bad, but has an increased chance for failure in the future. You repaired nothing The leg is still broken and "using it" will cause pain and further additional damages SMART as the acronym says , is the self monitoring system of the self drive healthiness. One day it tells you the drive is going to die. The job is done, the drive should must be replaced. In fact it makes no difference that you have a roughly 1 billion sectors GB hdd or a 4 billions sectors 2TB, the SMART reallocation table has only or sectors.

So I would make a modification to the accepted reply since it makes to think that you can repair a failed drive Hard drives have spare space for recovery reasons. The recovery happens automatically. Recovery tools only remap physically bad sectors to this spare space. Once remapped, when a read or write occur to a bad sector, the drive turns the access to the spare space, and hides the error.

It's something that the hard drive maintains internally, and in any event it would be a bad thing to do. SMART reports that your hard drive is failing! Resetting the counters will not change the fact that an error threshold for the drive has been exceeded.