Wx360 not an xbox iso fix

Details required :. Cancel Submit. Previous Next. Sumit Independent Advisor Independent Advisor. The error code means a device which does not exist was specified. It looks like the hard drive is wearing out. Download and run HDTune. Make screenshots of the following the health the error scan the benchmark Post back the screenshots. Disclaimer: This is a non-Microsoft website which would provide accurate and safe information.

There is no need to buy paid products to fix your computers as they do more harm than good sometimes. Share More sharing options Followers 0. Recommended Posts. Posted October 30, Link to comment Share on other sites More sharing options Yeah my xbox is modded OK update the firmware on that to latest.

Posted October 31, I Operation Started! I Writing Image LBA: 0 - W Waiting for buffers to recover W Waiting for hard disk activity to reach threshold level I Writing Layer I Closing Track I Finalising Disc W Waiting for device to become ready It is a common problem for soldered joints on the motherboard to crack. If this is the case, it is possible to solder or re-flow the connections. If your disc drive tray is stuck and will not open or close, then you have to manually eject the disc.

Follow these instructions to remove the faceplate and manually eject the drive. Remove any obstructions, and plug the console back in. If the eject button still doesn't work, your disc drive may need to be replaced. Discs that are extremely scratched will not be read by the console. Put a clean, unscratched disc in the the drive. If your Xbox plays the disc without issue, then the scratched discs were the problem. If the problem is not due to a scratched disc, then there might be dust on the lens of the optical drive that is keeping it from reading discs.

Remove the optical drive from the console and thoroughly clean it. If the Xbox will still not read discs after cleaning the optical drive, then your optical drive is likely faulty. If your Xbox isn't saving your in-game data, your hard drive is most likely either full or damaged. Make sure the hard drive is connected properly, assure there is enough free space for the save, and then attempt to save again.

If this does not work, you may need to replace the hard drive. Determining the malfunctioning component of your Xbox depends on how many red lights around the power button are flashing. If the bottom right red light is flashing on your Xbox , then your console is experiencing a hardware error. The console will still power on, and should display an error code on the screen it is connected to. The code will begin with an E, followed by two digits.

Some of the more common error codes can be found on this page, but more in-depth information can be found at Xbox-Experts' error code databse. When the left two lights are flashing red on the console, a component is overheating. It is likely that the fan will be running very loudly.

Shut the console off and let it cool down for a couple hours. To prevent this from happening in the future, make sure your Xbox is in a well-venitlated area and out of the immediate proximity of any walls, heaters, or other appliances.

The "Red Ring of Death" has occurred when all but the top right corner of the light ring are flashing red. A general hardware malfunction has occurred, affecting one or more components. The error message is not displayed directly, since the console doesn't power on, but it is possible to obtain the secondary error code from the Xbox.

Most, if not all, three-light errors in Xbox consoles are related to overheating. The most common issue is a cracked or cold solder joint underneath the GPU on the motherboard.

A flaw in the design of the heat sink allows the motherboard to warp in the area around the chip, which causes the chip to lose contact with the board. There are various fixes for the RROD, which include replacing the high-stress x-clamp, reflowing the GPU's solder connection, and also replacing the heat sink in older models with Microsoft's updated Zephyr heat sink.

To keep your Xbox from being affected by the RROD, keep it in a well-ventilated area and make sure the cooling vents are free from obstruction. If your Xbox begins to overheat, turn the power off and allow it to cool for at least an hour before continuing play.

Then drag the default. So, i have to remove the xbe file from the iso, how can i rebuild the iso after extracting the files then? Last edited by a moderator: Jan 28, Does anyone know of any other program that can repair or replace the xbe file so that its original? If your making a xbox 1 game backup, that you want to play on your , then yes, follow the above guide, and it should work. Anyone made a succesful working backup of san andreas that works on the ?